You may have read a report by a federal or state agency warning to be careful of the danger of too much ozone.   It is extremely important to understand what these warnings mean.

The distinction must be made of what the application of the ozone is for.
To remove serious odors, kill bacteria, and destroy mold it is important to perform 
High Ozone Shock Treatments in UNOCCUPIED ROOMS ONLY!

One must make the distinction that a high ozone level in an UNOCCUPIED ROOM has
absolutely nothing to do with any of the warnings issued for ozone use concerning air purification. . 

When you are NOT in the room at the time,  it is completely safe to use ozone at any level, as long as you wait until the ozone reverts back to oxygen to re-enter the room, which takes only about an hour or two. 
Since ozone is made up entirely of oxygen it can only revert back to natural oxygen once the ozonation process is completed. Therefore while high levels of ozone are toxic, within a short time ozone reverts back to non-toxic oxygen.

Our machines are designed to produce high levels of ozone when needed to perform 
High Ozone Shock Treatments  in UNOCCUPIED ROOMS.

High ozone levels are an absolute MUST to kill bacteria, mold, and have the ability remove strong odors. 
Remember unless you can achieve toxicity, in an UNOCCUPIED ROOM, you will never be able to kill mold and bacteria.  The definition of toxicity means to kill. Without toxicity you cannot kill any bacteria or mold.

Ozone concentrations of 0.05ppm are within most recommended safe exposure levels for air purification levels.

It is important to remember that when using ozone for air purification, control over the ozone level is THE most important feature. 
We've designed our machines to have the most control over the ozone output as compared to any other ozone machine made.

The "burst timer" built right into our smaller machines is designed to limit the amount of ozone to very low levels for use as an air purification device. 

Our smaller machines XT-120 - XT-800 can regulate the generator to only produce ozone for as little as 2 seconds out of a minute. This allows only very low levels of ozone to be present in a room.  That fact alone makes our units some of the safest on the market. 

Our smaller machines XT-120 - XT-800 have burst timers to limit the ozone production so that they can be used as low ozone level air purifiers that operate within "safe" levels. 
Yet these same machines can also perform high ozone treatments in small to medium sized rooms.

Ozone is basically self limiting. When the ozone level reaches to high a level it begins to irritate sinus passages, give you a sore throat, and possibly even a headache. 

Many people are worried about using an ozone generator because it can produce higher than the recommended exposure levels.

If you have ANY question about ozone safety you can simply use ozone when you are not in the room, and set the timer to turn the unit off before you re-enter the room.
 You can sanitize the room before you enter it. 
That way you will have NO exposure to ozone. No other air purifier or ionizer can do that.

By the way, we can PROVE that ozone kills bacteria, viruses, and mold. Please CLICK HERE to view our ozone, mold bacteria studies pages.

Ozone is sometimes misunderstood.  Ozone is O3, three atoms of oxygen linked together, rather than the two atoms of oxygen, O2,  we normally breath.  True O3 Ozone is made up entirely of oxygen. Ozone is NOT smog. Ozone is a compound that naturally occurs in nature. 

While ozone is sometimes mistakenly referred to as smog, SMOG is actually a combination of hydrocarbons, among them being CO² CO, and SO².

These hydrocarbons are most commonly created by the exhaust that comes from automobiles.

Ozone pushes these hydrocarbons back to the surface of the earth in order to use it's natural purification abilities to break them apart on a molecular level.

What is commonly called "ozone" in referring to the ground level air quality are really a mixture of these various toxic hydrocarbons, NOTO3 ozone.

We know that Ozone is a colorless gas, when we look at SMOG we can see that it is certainly not colorless.

In fact without Ozone we the Earth could not clean itself of the true SMOG which is the hydrocarbons.

Ozone has the beneficial role in smog reduction which is its ability to break down and oxidize hydrocarbons and particulates in the air. 

When it is said the ozone level is high and there is more SMOG it really means that while it is higher than normal at surface levels the real danger is not the O3 ozone, it is the hydrocarbons the heavier than air ozone is trying to clean.

When excessive amounts of man-made hydrocarbons are produced, there will be higher concentrations of ozone as a natural reaction to an unnatural situation. 

While very high levels of ozone are not good to breathe, the levels we find in the outside air fall within acceptable breathing limits.

Many attack ozone because it is a threat to the many ineffective but high profit air purification products being sold today such as ionizers.

Ionizers produce high profits for the sellers, sometimes well over 1000%, but they do not produce clean environments. Ionization can't kill mold or bacteria, and it can't break apart hydrocarbons.

Some ionizers now say they have a device on them that converts SMOG into oxygen. 
They are under mistaken assumption that ozone is the SMOG.
What it REALLY does is convert natural ozone into oxygen, thereby PREVENTING the natural ozone to clean the real SMOG which are the toxic hydrocarbons.

In the future ozone will replace many ineffective forms of air purification, including ionization, once the public becomes educated to the real benefits of ozone. 

There are many variables when it comes to square footage coverage. Using an ozone generator for home air cleaning, or for shock treatments require different ozone outputs.
The severity of a contaminated area is also another factor. 

When a manufacturer list a square footage rating it is meaningless since they can assign whatever square footage rating they want to their machines! The ONLY way to compare ozone generators is by comparing the milligrams per hour ozone output. This is the only way to gauge the power of the machine.
If a manufacturer does not list the ozone output in mg.hr. there is NO way to compare their machines, and they are probably hiding their units low output!

Of course ozone works! 
We sell thousands of ozone generators per year and our return rate is a fraction of 1%! 

Besides homeowners, mold remediation specialists buy our machines all the time. So do crime cleanup companies, fire, flood, & smoke cleanup companies as well as auto detailers, beauty salons, as well as restaurants and bars for cigarette smoke removal. 

Ozone generators kill mold spores, eliminate smoke, and more. They really do work.

We can PROVE that ozone kills bacteria, viruses, and mold. Just email us and request the independent scientific studies.

Yes, all of our ozone generators put out negative ions, any device that creates ozone will create negative ions as well.  Most ionizer products output more than 1,000,000 to 10,000,000 per cubic cm. This is way too much. Too much ionization turns your walls and furniture black with dirt, and causes breathing irritations.

According to air science, outdoor fresh air has 200 to 500 ions per cubic cm, indoor air has 100 to 200 per cubic cm and a forest will have 1,500 to 5,000 ions per cubic cm. 
Our ozone generators  produce reasonable levels of negative ions of about 10,000 to 30,000 per cubic cm., which is more than enough to gain the positive benefits of negative ionization.

Therefore, the amount of negative ions output from our series of products is good enough for giving indoor air that fresh clean smell. 

For purifying the air and removing odors only an ozone generator can kill viruses, bacteria, and mold spores. Ionization has no effect whatsoever on these compounds. Ionizers are "toys" compared to a real ozone generator. Ionization may make the air "smell" fresh but as soon as you turn the unit off the effect is over. Not so with ozone.

After careful testing we found extremely high amounts of negative ions were not effective in purifying the air. Too many ions gives a false sense of clean air and they become irritating very quickly. Too much ionization can cause headaches and sore throats, as well as turning the surfaces in your home black with a dusty film that is very difficult to wash away.

Six months after you start using an ionizer you will have MORE mold spores collected in your home than before you started! The use of ionization only makes the problem WORSE!

Read our page Ozone vs. Ionization and learn why ionization does cannot possibly kill mold.

 

WILL OZONE TRAVEL INTO WALLS AND KILL MOLD INSIDE A WALL?

No, ozone or anything else is going to travel inside the wall and kill the mold there.

If mold is living inside the walls the ONLY way to kill the mold is to take down the wall and then blast the inside of the walls with High Ozone Shock Treatments to make sure it is all dead.

Some companies are now saying that they have "specially created" ozone or that they use a form of "negative pressure" that will get the ozone inside of walls to kill the mold and bacteria inside them. 
This is simply not true.  Others say you can cut holes in the wall and "inject" ozone into the wall cavity to kill mold.

Many ozone companies have been sued by the government by making false claims such as that ozone will pass through walls.  But that is 100% NOT true, and anyone with common sense will recognize that.

Once again this is not going to work.   Let's think about this logically:
Every wall has a stud 16 inches apart that the wall board is nailed right up against.  They also have crossbeams halfway up the wall.  That means behind even a short 4 or 5 foot wall there are at least 8 separate cavities. 

So simply injecting the ozone into one cavity is only going to affect a very small cavity, not the entire opening behind a wall.   Even if "negative pressure" is used it will never be strong enough to draw the ozone through all the separate wall cavities.   It is simply not possible because the wallboard is nailed right up against the studs and there is no, or very little air leakage between them.

It does not make sense to cut 8, 12, or 20 holes in your walls to inject the ozone inside them.
Besides, the wallboard itself is most likely infected with the mold inside it's core so it is going to have to be replaced anyway.

The solution is to remove the entire wall, clean out any mold and mold infested insulation and nail up new wallboard.  Of course it is strongly recommended that ozone be used in this mold remediation process.

Some people ask us if they are going to open up the walls and rebuild anyway why bother using ozone at all? 
The answer to that is very simple.  One must make 100% sure that all the mold is killed behind a wall before they ever rebuild, or they leave the very real possibility that the mold will start growing behind the walls in just a short time once again.

One of the most common stories we hear almost every day is that someone has torn down their walls, did a quick mold cleanup, and then 6 months later the mold is growing once again.

We recommend that when walls are opened up that the entire room be blasted with very high levels of ozone, many times over a period of days, to make absolutely sure all the mold has been killed.

It is still wise to blast rooms that may even have mold behind the walls because it can kill the mold that is on the surface of the walls, and in the air, and therefore make it much safer to be in that room.

Even if you can't open up the walls and repair them right away, at least blasting ozone into the room will minimize the severe health consequences that can occur from even a slight mold exposure.

Ignoring a mold problem is not going to make it going to go away, and it will only continue to get worse over time. 
All the while the mold can be negatively affecting your health in an irreversible manner
It is imperative that rooms with mold in them be blasted with High Ozone Shock Treatments as soon as possible to kill any mold that is living in them.

Ozone, or anything else is NOT going to travel inside of walls no matter what anyone else may tell you. 
It is simply not possible.  We wish that it would so that it would make the job of mold remediation mush easier, but no gas, oxygen or ozone, can pass through your walls.

If you are using ozone for air purification it is recommended that the ozone purifier be placed high up, on the other side of the room.  This is so the ozone machine can clean the air between you and it. 

The idea is to purify the air, not breathe the ozone directly out of the machine.  Placing the unit high in the room helps disperse the ozone throughout the room more evenly.  Ozone is naturally heavier than air so it will naturally sink towards the ground. Using a slow moving fan, like a ceiling fan, can also help to disperse the ozone in the room.

If the ozone generator is going to be used in an unoccupied room in the shock treatment mode to kill mold, bacteria, or odors the unit should be placed at least table height or higher. 
Oxygen is O2, but Ozone is O3 so it will naturally sink to the floor. You can even place the unit higher than a table if possible.
We recently read on one ozone site to place the ozone generator on the floor. 
Nothing could be more wrong.

The ozone  is heavier than air and will sink to the floor anyway, and you will get better coverage in the room if you place the unit higher in the room.  Although the ozone will travel throughout the entire room, it might be a good idea to put the ozone near the source of the mold or odor, high up of course.

You can also use a slow moving fan to help distribute the ozone throughout the room more evenly.
Try not to use a fast moving fan because that will break apart the ozone much quicker.

Technically ozone can be flammable if it is made from pure oxygen. But the ozone we generate from our ozone generators uses the ambient oxygen, not external oxygen tanks.  Because of that we are not adding any extra oxygen to the air, we are only changing the existing oxygen into ozone. 
Thus, our ozone generators can be safely used around pilot lights with no additional risk of explosion.

Our XT line of ozone generators require very little maintenance. There is very little maintenance required on our no adjustment required U.S. Patented ozone elements. We use 24 carat gold plating on our elements internal components to help prevent corrosion.  The use of high temperature, shatter resistant tempered glass is also incorporated in our innovative, and U.S. Patented ozone elements.

Elements typically cost between $15 and $30 each. We sell them for cost and make no profit on them.

Our U.S. patented ozone elements are actually designed to avoid getting dirty. 
If they become dirty they can be blown out with an air stream to remove any dust.
We also include a special tool which can push out any dirt.
Running our units on full blasts also helps to burn off any accumulated dirt.

Old fashioned "plate" type ozone generators require much more maintenance.
Old fashioned plates become dirty over time, and their ozone outputs are greatly reduced.
They then have to be removed and scrubbed clean and reassembled in perfect alignment or they will spark and short out.

Old style ozone "plates" consist of  flimsy easily corroded steel screens and delicate thin pieces of glass or mica which must ALWAYS be in perfect alignment.
If not cleaned and aligned constantly, old style ozone "plates" will produce less ozone, and possibly even spark out dangerous high voltage electricity.   Even with all that work, their life span is notoriously short, usually about a year.

A typical 10,000 mg.hr plate type ozone generator has 3 parts for each "plate". That means there are 30 separate pieces that must be removed and clean and meticulously reassembled or disaster will occur.

Our U.S. Patented ozone element avoid all these problems.

Nothing is more annoying than calling a company, and having to press a series of buttons to hear a pre-recorded message.

At  MOLD-KILL a trained ozone technician is available to answer your phone calls during normal business hours. If you call nights or weekends you can leave a message on our voice mail.

If you get our voice mail please leave us a message and we will call you back as soon as possible.  Sometimes a person hangs up on us when we were less than 2 seconds from picking up the phone! 

If you don't leave a message we can't call you back, and you'll miss the best deal on an ozone generator you'll ever find. 

We are here for you, our valued customer, and we will give you 100% satisfaction in every aspect of our business.
We will NEVER reveal your phone number, email, or personal information to anyone, ever.

Many ozone generator companies have a pyramid system of selling their products. distributors pass the product to other distributors and each one gets a piece of your money. We sell directly at the best prices in the business.

If there is a fire or a flood a restoration team will bring an ozone generator. It will eliminate the odors in rooms, furniture, clothing and more. Only the strongest method of disinfection can do this and ozone is the choice of professionals. 

When a smoky nightclub needs to help clean the air ozone generators are used.
When mold is desired to be killed, ozone generators do the job.

For professional or home use ozone is the most effective disinfection method available.
The use of High Ozone Shock Treatments in unoccupied areas are extremely effective in removing strong odors.

 If it can be cleaned, ozone will clean it. We rarely receive a returned unit from someone who says it doesn't work. When used properly ozone can attack any odor problem.

We can PROVE that ozone kills bacteria, viruses, and mold. Just email us and request the independent scientific studies.

Professionals & homeowners alike love our ozone generators. Call us with your ozone needs. We will advise you as to what your particular situation demands.

DOES MOLD-KILL RENT OZONE GENERATORS?

Mold-Kill no longer rents ozone generators.  We have found out renting an ozone generator is not a good idea for the customer.  Many people tend to think a one time high ozone treatment will kill all the mold, and that the mold or odor problem will be completely solved.

If a basement has a mold problem ozone can be used to kill the mold and it's odor.  But a one time use is not going to solve a mold problem.  It is very tough to kill 100% of the mold in a room. 

While ozone can kill a great percentage of the mold, a slight bit will most likely still remain. 
Even after an ozone shock treatment some mold spores can live.  Soon the mold spores can begin to reproduce and multiply and the ozone treatment will need to be repeated.

When this happens you'll need to rent an ozone generator all over again. This can get expensive. 

Many odors sometimes come back, and high ozone shock treatments must be repeated.
Owning your own ozone generator is the way to insure when a mold or odor problem comes back you can quickly solve it before it spreads to other parts of your home.

Please Click here to see more reasons why renting an ozone generator is not always the best idea.
What If The Problem Comes Back?,  Low Powered Ozone Generator Rentals. Consider The Cost,  Money Back Guarantee?, Why Do Companies Rent Ozone Generators?

Some manufacturers are using a name that starts with an "A" to claim they have new form of ozone.
There are no "new" forms of ozone. Ozone is ozone. 

Some "A" machines claim to make higher forms of ozone such as O3, O4, O5, O6, O7, O8, O9, O10, O11, O12 etc.  This is nothing new at all.

The truth is that ALL corona discharge ozone generators, including ours, make higher forms of ozone including O3, O4, O5, O6, O7, O8, O9, O10, O11, O12 etc. 

In fact a corona discharge ozone generator cannot be made to produce just O3, and not the "higher forms" of oxygen such as O3, O4, O5, O6, O7, O8, O9, O10, O11, O12 etc. 

It is a naturally occurring scientific phenomena

But these higher forms of ozone only last for a very short time, seconds or less, as these unstable bonds quickly break apart very quickly due to the natural laws of physics. 

These higher the form of "A"ozone, linked oxygen, or activated oxygen or whatever some one calls it, the shorter in time it will last.  O12, for example, lasts for just milliseconds

Therefore, in our opinion, mentioning these higher forms of ozone formation is basically meaningless. 
Our corona discharge ozone generators make them, and all other brands do also, it's common knowledge in the ozone industry. 

Some of these "A" machines that are now claming phenomenal mg.hr. ozone outputs.
But they are achieving these high "ozone" outputs in a VERY deceptive way.

The industry standard practice is to ONLY count the molecular weight of the O3 Ozone.
NOT the other higher forms of oxygen which ALL corona discharge ozone generators produce.

That is why no reputable company bothers to count them as a TRUE ozone output.
The TRUE Ozone outputs of these types of machines are less than 1/6 of the claimed output
if even that much.

Certain laws of physics just can't be broken. Don't be fooled by gimmick machines.

They may even have a specific "A" name for this "ozone". 

Mold-Kill has only one secure order form for you to fill out. Fill out the simple shipping information EZ form, and submit your credit card payment with one click. You will immediately be E-mailed payment confirmation of your order. Your order will ship out within 24 business hours.

Mold-Kill uses the latest in 128 bit encryption secure server technology for fast and completely safe online credit card ordering. We handle thousands of dollars a day, and have never had even one incident of credit card fraud. 

No one but our bank will ever see your credit card number. We don't even see your number!

We will NEVER reveal your phone number, email, or personal information to anyone else ever!
All purchases placed through Mold-Kill made with Visa, Master Card, or American Express are covered by the 100% Fraud Protection guarantee each of those companies offer since we are a verified merchant.
 

Mold-Kill is a member of The Better Business Bureau, and proudly displays their BBB Online reliability program seal.  The BBB seal means we meet their selling standards. Click on the seal to learn more about what this means.

Mold-Kill is also a member of SquareTrade which means we have a superior track selling record, and that our business identity is verified. Click on the seal to learn more about what this means.

Rest assured when you buy from Mold-Kill that your order is handled professionally, and that the customer is always protected from the fraud of false air purifier merchants, scam artists, hackers, bulk emailers, and telemarketers.

Be sure to ONLY order from a company that uses a DIRECT connection to Authorize.net's secure web site like we do. That's your assurance that a company is real, and that your money is protected.